Konfigurasi VLAN 1 Router untuk 3 Switch Cisco Packet Tracer




Assallamu'allaikum wr...wb...

Siang kawan ,pada kesempatan yang baik ini, saya akan memberikan sedikit materi yang saya pahami atau saya praktean pada hari ini.
yaitu Konfigurasi VLAN1 Router 3 Switch dan 1 Server Cisco Packet Tracer

Tahap Pelaksanaan Kegiatan 

1.Buka aplikasi cisco packet tracernya kemudian siapkan

             3 buah switch, 1 router, 8 buah pc,  1 server


2. Setting Switch 1

SWITCH 1
 
Switch>
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 50
Switch(config-vlan)#name bedha
Switch(config-vlan)#vlan 60
Switch(config-vlan)#name cholifah
Switch(config-vlan)#int fa0/1
Switch(config-if)#swit
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 50
Switch(config-if)#exit
Switch(config)#int fa0/3
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 50
Switch(config-if)#exit
Switch(config)#int fa0/4
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 60
Switch(config-if)#exit
Switch(config)#int fa0/5
Switch(config-if)#wi
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 60
Switch(config-if)#exit
Switch(config)#do sh vlan
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa0/2, Fa0/6, Fa0/7, Fa0/8
                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12
                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16
                                                Fa0/17, Fa0/18, Fa0/19, Fa0/20
                                                Fa0/21, Fa0/22, Fa0/23, Fa0/24
                                                Gig0/1, Gig0/2
50   bedha                        active    Fa0/1, Fa0/3
60   cholifah                          active    Fa0/4, Fa0/5
1002 fddi-default                     active    
1003 token-ring-default               active    
1004 fddinet-default                  active    
1005 trnet-default                    active    
      
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa 0/2
Switch(config-if)#swit
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk 


 3. Setting Switch 2

SWITCH 2
Switch>
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 50
Switch(config-vlan)#name bedha
Switch(config-vlan)#vlan 60
Switch(config-vlan)#name cholifah
Switch(config-vlan)#int fa0/3
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 50
Switch(config-if)#exit
Switch(config)#int fa0/4
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swit
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 50
Switch(config-if)#exit
Switch(config)#int fa 0/2
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 60
Switch(config-if)#exit
Switch(config)#int fa 0/5
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access 
Switch(config-if)#swi
Switch(config-if)#switchport acc
Switch(config-if)#switchport access vlan 60
Switch(config-if)#
Switch(config-if)#
Switch(config-if)#exit
Switch(config)#
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa0/6
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tru
Switch(config-if)#switchport mode trunk 

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state to up

Switch(config-if)#exit
Switch(config)#

4. Router

 ROUTER
Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int gig 0/0
Router(config-if)#

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int gig 0/0
Router(config-if)#ip add 192.168.10.4 255.255.255.252
Bad mask /30 for address 192.168.10.4
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int gig 0/1
Router(config-if)#ip add 192.168.20.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int gig 0/0.50
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.50, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.50, changed state to up

Router(config-subif)#enc
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 50
Router(config-subif)#ip add 192.168.50.129 255.255.255.128
Router(config-subif)#no shut
Router(config-subif)#exit
Router(config)#int gig
Router(config)#int gigabitEthernet 0/0.60
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.60, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.60, changed state to up

Router(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 60
Router(config-subif)#ip add 192.168.60.65 255.255.255.192
Router(config-subif)#no shut
Router(config-subif)#exit
Router(config)#


5. Akses DNS di Web Browser 
6. Router

 ROUTER
Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int gig 0/0
Router(config-if)#

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int gig 0/0
Router(config-if)#ip add 192.168.10.4 255.255.255.252
Bad mask /30 for address 192.168.10.4
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int gig 0/1
Router(config-if)#ip add 192.168.20.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int gig 0/0.50
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.50, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.50, changed state to up

Router(config-subif)#enc
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 50
Router(config-subif)#ip add 192.168.50.129 255.255.255.128
Router(config-subif)#no shut
Router(config-subif)#exit
Router(config)#int gig
Router(config)#int gigabitEthernet 0/0.60
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.60, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.60, changed state to up

Router(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 60
Router(config-subif)#ip add 192.168.60.65 255.255.255.192
Router(config-subif)#no shut
Router(config-subif)#exit
Router(config)#

7. Akses DNS di Web Browser 


SELESAI........



Komentar

Posting Komentar

Postingan populer dari blog ini

Konfigurasi Pada Subcriber Internet Telepon (BAB 15)

 Konfigurasi Pada Subcriber Internet Telepon a. Instalasi Subscriber secara umum internet telepon Melakukan Dial-Up Ada beberapa cara yang dapat dilakukan untuk terkoneksi dengan internet. Salah satu caranya adalah koneksi internet dengan dial-up yaitu akses internet dengan menggunakan jalur telepon. Untuk melakukan koneksi ini, perangkat yang dibutuhkan adalah sebagai berikut ini:  ~ 1 unit komputer  ~ 1 modem  ~ 1 sambungan telepon  Hal yang harus dilakukan adalah : ~ Berlangganan ke salah satu ISP terdekat  ~ Memasang modem ke komputer  ~ Menginstall software internet yang disediakan oleh ISP  ~ Menghubungkan komputer (dial-up) ke ISP   Kelamahan dari Dial-Up adalah sebagai berikut :  a) Saat melakukan koneksi internet, telepon tidak dapat digunakan untuk sambungan keluar atau menerima telepon. b) Akses ini menggunakan modem analog, sehingga kecepatan akses lebih rendah dibandingkan metode la...
Baca selengkapnya